Westerbeke 38B FOUR Manual del operador Pagina 35
- Pagina / 108
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
PREPARATION FOR STARTING
This section of the manual provides the operator wtth preparation, initial starting, break-in, starting (cold
or
warm), and stopping procedures. Follow the procedures as presented,
for
the conditions indicated, and
your Westerbeke engine set
will give you reliable performance and long service life.
Fill
your
engine with oil up
to
or
near the upper limn on the
dipstick (the installation angle may have an effect
on
the
dipstick reading).
Select readily available lubricating oil with
an
API
specification
of
CC
or
CD
and an SAE number suitable
for the temperature in
your
operating area (see page 60). For
the quantity
01
oil needed in your engine, refer
to
the "SYS-
TEM SPECIFICATION" section
01
this manual, page 13 for the
W
35B, page 16
lorthe
W 38B, and page 19 for the W 42B.
Fill the
JS transmission
to
the FULL mark
on
the dipstick with
the correct lubricant. (The
JS transmission takes 1 U.S. qt
or
1 liter
of
oil. Refer
10
your engine's "SYSTEM SPECIFICA-
TION"
section
of
this manual
lor
a listing of oil grades
to
be
used in this engine.)
UPPER
LIMIT
~~:;;;:;_;:;;_~::_~
__
(_HORMRL
LEVEL)
LOWER
LIMIT
Each unit is supplied with a coolant recovery kit (#24977)
as
standard equipment,
to
which the following ap-
plies:
A.
Remove the pressure cap from the engine's exhaust manifold and slowly fill the engine's
COOling
sys-
tem with a mixture of water and antifreeze
suitable for your temperature zone. (See the "COOLING SYS-
TEM"
section
01
this manual, page 53.) Operate the engine and observe the coolant level
in
the manifold.
Maintain this level
to
the base
01
the Iiller neck. Once the engine reaches its operating temperature (170
-
190'
F),
make sure there is coolant flow
to
the domestic water heaters when installed. Top off the cool-
ing system
and Instalilha pressure cap.
8.
Make sure the plastic recovery tank is properly mounted near the unit (with the bracket provided), in a
location where it can be monitored and filled easily. The recovery tank should be mounted at manifold
level
or
above. In these installations that require
it,
the plastic recovery tank can be mounted below the
exhaust
manifold's level.
c.
Add coolant
to
the plastic tank after the engine has been started and after the engine's operating
temperature has been reached
to
make sure all air is expelled from the manifold and the engine's cool-
ing system. With the manifold filled and the pressure cap installed, fill the plastic recovery tank half full.
Monitor daily and add coolant as needed.
Fill the fuel
lank
with a good grade of NO.2 diesel fuel and prime the fuel system up
to
the engine (see page
44). When
returning fuel is free
01
air, the engine's fuel system is bled and the engine is ready
to
start.
NOTE: When the PREHEAT switch is depressed, the glow plugs in the cylinder head are ener-
gized; use the PREHEAT switch intermittently
to
prevent overheating the glow plugs.
Make sure the
Installation Checks have been made in accordance with those specified
in
the "INSTALLA-
TION CHECKS"
section
01
this manual (refer
to
page 21).
33
Westerbeke Diesel
Engines
- WESI'ERBEKE 1
- SAFETY PRECAUTIONS 2
- 1 Westerbeke Diesel 3
- . 4
- Diesel Engines 5
- Marine Diesel Engine 10
- Lift pump 11
- Oil Fill 12
- 90° Exhaust Elbow 12
- THREE MARINE DIESEL ENGINE 14
- GENERAL SPECIFICATIONS 14
- 6 ft (1.8 m) 15
- + 000 - 100) at full open 16
- + 000 - 100) at full open 19
- ± 0.5' BTDC (Static) 21
- AlnIl:Nan:~~~~~B~~==~' 23
- Rigging and 24
- Engines 24
- Westerbeke Diesel Engines 27
- Exhaust System 28
- ." 29
- * Manufactured 31
- + ) battery connection 34
- 190' 35
- Westerbeke 38
- 30 seconds at a time 41
- Break-In 43
- FITTING 45
- Iills. Prevent 46
- ,-----/---€,i\l--\ 49
- ----+fT 50
- ,----:---"1;" 51
- ~1l1)~,i 52
- 1'1 53
- FUNCTION 55
- MANIFOLD 55
- PRESSURE 55
- '1 56
- : i: ' 56
- REPLACE 57
- IMCOMING 59
- Crankcase 64
- NEUTRAL 66
- "j/ 68
- I I i 69
- 10-13/10-14 70
- Starling the Engine 71
- Shifting 71
- Freewheeling 71
- Cooling Problems 72
- Annual Checks 73
- Daily Checks 73
- Winter Checks 73
- General Checks 73
- Walter V-Drives 75
- RV'IO 76
- ~/LOCKING 77
- "H" 78
- Maintenance 79
- I terminal on the 81
- + and - ground 82
- + 140 psi 86
- W 42B FOUR Engine) 87
- ADJUST VALVES 88
- ~'"'' 89
- 50-50 solution 91
- 38B, and page 19 for 91
- Batleries 93
- 4. Check the condition 94
- QapSQ[9W 95
- A Starter 97
- Weslerbeke Diesel Engines 100
- YOUR NOTES 104
Relacionado con productos y manuales para Motor Westerbeke 38B FOUR
Motor Westerbeke 33a El manual del propietario
(33 paginas)
(33 paginas)
Motor Westerbeke 120D-TWO Manual de servicio
(59 paginas)
(59 paginas)
Motor Westerbeke 108B Manual de instalación
(62 paginas)
(62 paginas)
Motor Westerbeke 108B Manual de instalación
(60 paginas)
(60 paginas)
Motor Westerbeke WPDS-20 Manual del operador
(114 paginas)
(114 paginas)
Motor Westerbeke 33a Manual de servicio
(117 paginas)
(117 paginas)
Motor Westerbeke 120D-TWO Manual de usuario
(72 paginas)
(72 paginas)
Motor Westerbeke 21A Manual de instalación
(46 paginas)
(46 paginas)
Motor Westerbeke 108C SIX Manual de usuario
(12 paginas)
(12 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales